Quick Start Guide
MODEL PPU916RS
Lenmar PowerPort Laptop Battery – The Ultimate Power On The Go
STEP 1.) LOCATING THE REQUIRED VOLTAGE
B
C
A
DC R
A
TING:16V
TING:16V
A
DC
R
VIN:
=
16VDC
SIDE OF LAPTOP
AC ADAPTER LABEL
BOTTOM OF LAPTOP
YOU CAN FIND THE REQUIRED DC OUTPUT VOLTAGE ON ONE OF THE THREE OPTIONS SHOWN ABOVE.
STEP 6.) OPERATING THE PPU916RS
STEP 2.) VERIFYING CENTER POSITIVE POLARITY
DC “OUT”PORT
LOOK FOR THE SYMBOL ABOVE IN ANY OF THE THREE LOCATIONS MENTIONED ABOVE.
IF THIS SYMBOL DOES NOT MATCH DO NOT USE PPU916RS.
OUTPUT CABLE
OUTPUT TIP
DC “IN”PORT
PPU916RS
CONNECT THE POWER TIP TO THE OUTPUT CABLE AND PLUG IN AS SHOWN ABLOVE.
STEP 3.) SETTING THE CORRECT VOLTAGE ON THE PPU916RS
SLIDING BUTTON BETWEEN 16V/19V SELECTION
STEP 7.) CAPACITY INDICATOR
LED
BUTTON 1 2 345
SLIDE THE SWITH TO MATCH THE REQUIRED VOLTAGE YOU FOUND ON STEP 1.
CHARGING
INDICATOR
LED 1 indicates 0% to 25%
CAPACITY
INDICATOR
LED 2 indicates 25% to 50%
LED 3 indicates 40% to 60%
STEP 4.) LOCATING THE CORRECT ADAPTER TIPS
LED 4 indicates 75% to 100%
PPU916RS
CHARGING TIP
PRESS THE BUTTON ON THE TOP OF THE PPU916RS TO SHOW
REMAINING CAPACITY, THERE ARE 4 INDICATOR LIGHTS.
POWER TIP
VERIFY THE CORRECT ADAPTER TIPS NEEDED FOR YOUR LAPTOP BY VISITING
WWW.LENMAR.COM/ADAPTERTIPS.
STEP 8.) USB POWER PORT
STEP 5.) CHARGING THE PPU916RS
CHARGE TIP
USB PORT
THE PPU916RS HAS A BUILT IN USB PORT FOR THE CONVENIENCE OF CHARGING YOUR
CELL PHONE, PDA, MP3 PLAYER OR ANY OTHER DEVICE THAT CAN BE CHARGED FROM A
STANDARD USB PORT. FOR BEST RESULTS USE AN OEM OR FACTORY APPROVED USB
CABLE. NOTE: THIS IS NOT COMPATIBLE WITH TABLETS.
PPU916RS
ORIGINAL NOTEBOOK AC ADAPTER
NOTE: FOR MORE SPECIFIC DETAILED INSTRUCTIONS PLEASE REFER TO THE COMPLETE
OWNER’S MANUAL.
USING YOUR LAPTOP’S ORIGINAL AC ADAPTER, PLUG THE CHARGING TIP FOUND IN
STEP 4 INTO YOUR AC ADAPTER, THEN PLUG INTO THE “IN”PORT OF THE PPU916RS.
2.
2.) Review the power ID plate on your notebook or
laptop computer to be powered. This is usually
found on the bottom of your computer. Look
for the word “DC RATING or INPUT”followed by
a number and VDC*.
Model PPU916RS
TING:16V
A
Lenmar PowerPort Laptop Battery – The Ultimate Power On The Go
DC R
Important Safety Instructions are included.
Please read the entire manual before use.
Example: DC RATING: 16VDC or INPUT: 16VDC
BOTTOM OF LAPTOP
Owner’s Manual
Thank you for purchasing the PPU916RS PowerPort Laptop Battery for notebook and laptop computers. The
PPU916RS provides a 16 & 19 VDC output that can provide up to 3 hours of additional runtime. Also
included is a USB output port for charging your cell phone, PDA, MP3 player or any other device that can be
charged from a standard USB port. Please note: This is not compatible with tablets.
3.
3.) Review the voltage indication marked next to
the input jack on the notebook or laptop
computer to be powered.
Pre-Operation Setup
Please make sure you follow the two steps outlined below to determine the right settings compatible with
your notebook or laptop computer.
VIN: = 16VDC
Example: VIN: = 16VDC or 16V DC
Step 1. Determine Polarity
The PPU916RS works only with notebook and laptop computers that have “center positive”polarity. Please
conꢀrm that your laptop has “center positive”polarity before using the PPU916RS. You may look for the
below in your notebook or laptop user manual (please see image to the right).
SIDE OF LAPTOP
*Note: The speciꢀc notation “VDC”might not be indicated. Instead the following international symbol
shown might be used 16 . In some cases you may determine the desired voltage is between whole
DO NOT USE the PPU916RS if your device shows “center negative” polarity.
CENTER POSITIVE
numbers such as 15.5VDC. In this case use the next higher voltage setting. For example, use 16VDC if
the desired voltage is 15.5VDC.
Step 2: Determine Voltage Required
Please determine the required voltage needed for your
SLIDING BUTTON BETWEEN 16V/19V SELECTION
notebook or laptop computer. Once you have determined
the correct voltage, slide the switch on your PPU916RS
to either 16V or 19V.
Operating Instructions
The PPU916RS must be charged before initial use to power up your notebook or laptop computer.
In some cases you may determine the desired voltage is between whole numbers such as 18.5VDC. In this case
you would use the 19V setting. In the case of 20VDC, also choose the setting of 19VDC.
Selecting the Right Battery Tip
The PPU916RS comes with 8 power tips, and 7 charging tips and one 30”power cord. These tips will
allow you to charge the PPU916RS and also power your laptop.
Determine the correct power tip and connect it to the included 30” power cord then plug it into your
laptop. The power tips consist of models L01D, L51D, L52D, L53D, L54D, L55D, L61D, and L62D. The
charging tips are made to connect to your existing AC Adaptor and then be plugged into the“IN”jack on
the PPU916RS. They are the right angle tips consisting of models: L01, L51, L53, L54, L55, L61 and L62. You
may also use your existing AC Adapter tip if it ꢀts.
1.
DC R
A
TING:16V
1.) Review the power or ID plate on the original
AC / DC power supply that comes with your
notebook or laptop computer. Look for the word
“DC RATING or OUTPUT”followed by a number
and VDC*.
Example: VIN: = 16VDC or 16V DC
AC ADAPTER LABEL
CHARGING TIP
POWER TIP
1.
2.
Notice
Select the adapter tips that correspond to your laptop or notebook brand and model by visiting www.len-
mar.com/adaptertips. Verify the ꢀt of the power tip by plugging it into the input jack on your laptop.
• Keep the PPU916RS dry, if it gets wet wipe it dry immediately.
• Use and store it in normal temperature environments.
• Handle the PPU916RS carefully, do not drop it. Do not use the PPU916RS if the cords become damaged.
• Keep the PPU916RS away from dust and dirt; wipe it with a cloth occasionally to keep it clean.
• There are no user serviceable parts inside! Modifying or tampering with its internal components can cause a
malfunction and will invalidate its warranty. If your PPU916RS is not performing as it should during the
warranty period, contact Lenmar for warranty service.
It is important that the center contact or pin be the correct size to insure proper electrical contact. The tip
should slide in as easily as the original adapter tip. Do not force it. If it does not ꢀt easily please verify that you
have the correct tip listed in our reference.
Charging the PPU916RS
To charge the PPPU916RS, use your notebook or laptop
computer’s existing AC Adapter. Connect the AC Adapter
PRODUCT SPECIFICATIONS
Charge time: Approx 5 hours.
CHARGE TIP
Chemistry: Lithium-Polymer
Charge input: 15V ~ 25 V 2.5A~ 4A adapter input
Output Wh: 63Wh / 16,500mAh
to the correct charging tip. Then plug in the tip into “IN”
port of the PPU916RS. Approximate charge time is 5
hours. You will see an indicator on the 5th LED light. The
light will be red while charging and will turn blue once
the charge is complete.
Discharge output: 5.3 V, 16V, 19V
PPU916RS
ORIGINAL NOTEBOOK AC ADAPTER
Limited 1 Year Warranty
Lenmar product is warranted to be free of defective parts and workmanship for stated period from the
original date of purchase when sold through our website or our authorized retailers. Warranties are not
transferable. The warranty excludes damage resulting from accident, misuse, modiꢀcation, delay or loss of
use, damage to equipment or by normal wear and tear.
Connecting the PPU916RS to your laptop
Plug the supplied 30”power cable into the “OUT”port on the PPU916RS. Attach the correct power tip to
the other end of the cable and plug this into the “DC IN”port of your laptop.
ALL WARRANTY CLAIMS ARE PROCESSED ONLINE AT THE FOLLOWING LINK:
WWW.LENMAR.COM/WARRANTY
OUTPUT CABLE
OUTPUT TIP
Warranty claims made after 60 days from the original date of purchase, will require a processing fee. Details
will be included while completing the online warranty request. Payment can be made via credit card when
completing the warranty form or a check can be included with the package when it is returned to Lenmar.
Once the request is completed, you will be emailed with a conꢀrmation WRA number and instructions on how
to return the item for a warranty replacement.
PPU916RS
Capacity Indicator
Press the button on the top of the PPU916RS to show remaining capacity, there are 4 indicator lights.
LED
BUTTON 1 2 345
Proposition 65 Notice (California)
The following statement is required in the state of California pursuant to the settlement of an action brought
by the Mateel Environmental Justice Foundation against multiple electronics and appliance manufacturers
CHARGING
INDICATOR
LED 1 indicates 0% to 25%
• WARNING: Handling the cord on this product will expose you to lead, a chemical known to the
state of California to cause birth defects or other reproductive harm. Wash hands after handling.
CAPACITY
INDICATOR
LED 2 indicates 25% to 50%
LED 3 indicates 40% to 60%
Contact Lenmar Enterprises, Inc.
mar.com/adaptertips.
LED 4 indicates 75% to 100%
For additional questions, comments, or to explore other Lenmar power solutions, visit our website at:
PPU916RS
USB Power Port
USB PORT
The PPU916RS has a built in USB port for the convenience of
charging your cell phone, PDA, MP3 player or any other
device that can be charged from a standard USB port. For
best results use an OEM or factory approved USB cable.
Please note: This is not compatible with tablets.
313-100-33-0410 r2 y1
Lithium-Polymer battery must be
recycled or disposed of properly.
4.
3.
|