CLUB SERIES SMITH MACHINE
ASSEMBLY INSTRUCTIONS
Part # 7187601
Rev. B
1
Revision:12/4/01
11 3/8 X 2-3/4” BOLT
12 3/8 X 3” BOLT
13
3/8” LOW
HEIGHT LOCK
NUT
14
3/8” SAE
WASHER
18 19
RH CAP
(BLACK/WHITE/PLATINUM)
15
RH
WASHER
3
16
2
1
19
11 3/8 X 2-3/4”
8
19
18
19
12 3/8 X 3”
3
19
9
12 3/8 X 3”
18
19
13
15
14
11 3/8 X 2-3/4”
18
FIGURE 1
STEP 1:
• LOOSELY assemble the two WEIGHT HORNS (9) and the BOTTOM CROSS BRACE (3) to the RIGHT and LEFT UPRIGHTS (1 &
16) as shown in FIGURE 1 using using four BLACK RH CAPS (18), four RH CAPS (19), four 3/8 X 3” BOLTS (12), eight 3/8”
SAE WASHERS (14), eight 3/8” RH WASHERS (15) and four 3/8” LOW HEIGHT LOCK NUTS (13) as shown in FIGURE 1.
• LOOSELY assemble the TOP CROSS BRACE (2) to the TOP SET of holes of the RIGHT and LEFT UPRIGHTS (1 & 16) as shown
in FIGURE 1 using using two RH CAPS (19), two 3/8 X 2-3/4” BOLTS (11), two 3/8” SAE WASHERS (14) and two 3/8” RH
WASHERS (15) as shown in FIGURE 1.
• LOOSELY assemble the BAR SUPPORT RACKS (8) to the outside of the RIGHT and LEFT UPRIGHTS (1 & 16) as shown in
FIGURE 1 using eight BLACK RH CAPS (18), eight RH CAPS (19), six 3/8 X 2-3/4” BOLTS (11), two 3/8 X 3” BOLTS (12),
sixteen 3/8” SAE WASHERS (14), sixteen 3/8” RH WASHERS (15) and eight 3/8” LOW HEIGHT LOCK NUTS (13) as shown in
FIGURE 1.
• SECURELY tighten all connections made to up to this point.
4
16
1
9
19
15
14
11 3/8 X 2-3/4”
18
13
FIGURE 2
STEP 2:
• SECURELY assemble the four WEIGHT HORNS (9) to the RIGHT and LEFT UPRIGHTS (1 & 16) as shown in FIGURE 2 using
using eight BLACK RH CAPS (18), eight RH CAPS (19), eight 3/8 X 2-3/4” BOLTS (11), sixteen 3/8” SAE WASHERS (14),
sixteen 3/8” RH WASHERS (15) and eight 3/8” LOW HEIGHT LOCK NUTS (13) as shown in FIGURE 2.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
5
!! IMPORTANT !!
REMOVE TAPE FROM BOTH ENDS OF THE
HOUSINGSAS SHOWN!
DO NOT REMOVE PLASTIC TUBES ON THIS STEP!
4
HOUSING
7
FIGURE 3
STEP 3:
• Insert the shaft of the HOUSINGS (4) into the ends of the SMITH BAR (7) as shown in FIGURE 3.
6
16
1
10
6
7
4
8
5
FIGURE 4
STEP 4:
•
Hook the SMITH BAR (7) onto slots of the BAR SUPPORT RACKS (8).
• Slide one GUIDE ROD (10) through the upper hole in the UPRIGHT (1 & 16) and proceed to slide one 1” SHAFT COLLAR (6)
over the bottom of the GUIDE ROD (10) as shown in FIGURE 4.
•
CAREFULLY lower the GUIDE ROD (10) through the HOUSING (4) on the SMITH BAR (7). (NOTE: Allow the GUIDE
RODS (10) to push the plastic insert out the bottom of the HOUSINGS (4). Discard these inserts.)
•
CAREFULLY slide one BAR STOP (5) over the end of the GUIDE ROD (10). Hook BAR STOP (5) into the slots of BAR
SUPPORT RACKS (8) as shown.
•
Insert the GUIDE ROD (10) into the bottom hole of the UPRIGHT (1 & 16). Repeat this step on the other side.
7
16
SECURELY
TIGHTEN!
6
1
10
FIGURE 5
STEP 5:
•
Slide the 1” SHAFT COLLARS (6) up the GUIDE RODS (10) to the bushing of the UPRIGHTS (1 & 16) and SECURELY
TIGHTEN.
8
17
1
FIGURE 6
STEP 6:
• If necessary, apply the FOREIGN LANGUAGE PLACARD LABEL (17) to the PLACARD LABEL on the RIGHT UPRIGHT (1) as
shown in FIGURE 6.
• This equipment is designed to be stable during normal use, however, in order to ensure the saftey of personnel during
potential misuse of the equipment, we strongly recommend that this equipment be securely fastened to the floor of the
facility with 1/2” (12mm) fasteners compatible with the flooring material of the facility.
9
CAUTION-PLEASE READ
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
2. Do not allow minors or children to play on or around this equipment.
3. Exercise with care to avoid injury.
4. Consult your physician before beginning any exercise program.
WARRANTY INFORMATION
10YEARS
3 YEARS
1 YEAR
STRUCTURUAL FRAME
PILLOW BLOCKS, PULLEYS, WEIGHT PLATESAND GUIDE RODS
CABLES
90 DAYS
UPHOLSTERY
PREVENTATIVE MAINTENANCE TIPS
Action
DAILY WEEKLY QUARTERLY BI-ANNUALLY AS NEEDED
CLEAN
Upholstery
Guide Rods
Hand Grips
X
X
X
INSPECT
Visual Overall
Cables
Hardware
Frame
X
X
X
X
X
Hand Grips
LUBRICATE
Guide Rods
X
Clean:
• Upholstery with mild soap and water.
• Guide rods with a cotton cloth.
• Hand grips with mild soap and water.
• Frame damage can be repaired with touch-up paint can be purchased from your LifeFitness customer service representative at
(800)351-3737.
Inspect:
• Cables for wear or damage and proper tension (should not exceed 3/4” deflection.) Pay close attention at bends and attachment
points.
• Hardware should be checked for looseness. Tighten as required.
• Frames should be inspected for wear or damage.
• Hand Grips should be checked for wear or damage
Lubricate:
• Lube the Guide Rods. Apply the lubricant to a cotton cloth, then run the cotton cloth up and down the guide rods as needed. Do not
spray lubricant directly on the Guide Rods.
Thank you for purchasing the LifeFitness CLUB SERIES SMITH. If unsure of proper use of equipment,
call your local LifeFitness distributor or call the LifeFitness customer service department at
(800) 351-3737.
10
|