INSTRUCTION MANUAL
Meade114 EQ-DS
4.5" Equatorial Reflecting Telescope
Meade Instruments Corporation
– 3 –
TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Standard Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Unpacking and Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Balancing the Telescope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Alignment of the Viewfinder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Understanding Celestial Movements and Coordinates. . . . . . . . . . . . . . 8
Lining Up with the Celestial Pole. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Using the Telescope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Using Setting Circles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Calculating Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Mount and Tripod Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . 12
Collimation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
a. Correct Collimation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
b. Diagonal Holder Adjustments . . . . . . . . . . . . . . . . . . . . . . . 12
c. Primary Mirror Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . 13
d. Star Testing the Collimation . . . . . . . . . . . . . . . . . . . . . . . . 13
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
– 4 –
Key to Fig. 1
1. Tripod legs
25. Telescope front dust cover
2. Equatorial mount
26. Viewfinder bracket thumbscrews
27. R.A. setting circle
3. R.A. flexible cable control
4. Dec. flexible cable control
5. Counterweights
28. Dec. setting circle
29. Latitude dial
6. Counterweight shaft
7. Counterweight locks
8. Safety washer/thumbscrew
9. Latitude lock (reverse side, see inset)
10. Polar axis
30. Azimuth lock
31. Focus knobs
32. Optional motor drive gear (option not
available with this model)
33. Azimuth base
11. Latitude adjustment knob
12. Optical tube assembly
13. Optical tube saddle plate
14. Cradle rings
34. Viewfinder focuser
35. Azimuth circle
36. Cradle ring attachment lock knob
37. Cradle ring attachment
38. Tripod leg Phillips-head fastener screws
39. Tripod-to-mount wingnuts
40. Accessory shelf
15. Cradle ring lock knobs
16. Viewfinder bracket mounting bolts
17. Focuser
18. Focuser thumbscrew
19. Eyepiece
41. Eyepiece holder slots
42. Tripod leg brace supports
43. Tripod leg lock knobs
44. Optional motor clutch
45. Optional motor mount shaft (option not
available with this model)
20. Viewfinder bracket
21. Declination axis
22. R.A. lock (reverse side, see inset)
23. Dec. lock
24. 5 x 24 viewfinder
– 5 –
26
13
24
21
36
28
10
20
Reverse
side
16
26
34
23
5
6
7
Fig. 1a: Model 114 EQB-1: Viewfinder assembly.
27
45
22
19
18
32
8
44
11
9
29
35
18
17
Reverse Side
33
38
30
31
Fig. 1c: Model 114 EQ-DS: Equatorial mount.
Fig. 1b: Model 114 EQ-DS: Focuser.
24
19
25
14
15
12
37
1
42
2
4
41
40
3
39
43
Fig. 1d: Model 114 EQ-DS: Tripod and tray.
Fig. 1e: Model 114 EQ-DS: Optical tube assembly.
– 6 –
INTRODUCTION
The Meade 114 EQ-DS is an easy-to-operate, high performance 4.5" (114mm) reflecting telescope,
intended for astronomical observing. Equipped with a deluxe equatorial mount and aluminum tripod, the
telescope’s motion is continuously adjustable for tracking celestial objects. Your telescope comes to you
ready for adventure; it will be your companion in a universe of planets, galaxies, and stars. Please note
that the Meade 114 EQ-DS is a Newtonian reflecting telescope optimized for astronomical observing
performance, and is not intended for terrestrial observing.
This Manual
These instructions detail the set-up, operation, specifications, and optional accessories of your Jupiter
114 EQ-DS. In order that you may achieve maximum enjoyment of the instrument, we urge that
you take a few minutes to read all of this manual before making first observations through the telescope.
Standard Equipment
•
•
•
Complete optical tube assembly with a 4.5" (114mm) diameter primary mirror, viewfinder mounting
bolts with mounting nuts and rack-and-pinion focuser. Mirror focal length = 1000mm; f/8.8
Equatorial mount with pre-attached heavy duty, continuously adjustable, aluminum tripod and leg
braces.
Accessories: H 25mm (40x) eyepiece (.965" O.D.), H 12.5mm (80x) eyepiece (.965" O.D.),
SR 4mm (250x) eyepiece (.965" O.D.)
3x Barlow lens
Cradle rings with lock knobs
5 x 24 viewfinder and bracket
Counterweight with counterweight shaft
Flexible cable controls for both telescope axes
Accessory tray
UNPACKING AND ASSEMBLY
Your Meade 114 EQ-DS comes to you packaged almost entirely pre-assembled. (References in this
section—e.g. (6)—are to Fig.1a - 1e unless otherwise specified.)
•
•
Remove and identify the telescope’s Standard Equipment listed above.
The three tripod lock knobs (43) have been removed from the
bottom section of each tripod leg to insure safe arrival of the tripod
assembly. To install, thread in each tripod lock knob into the
threaded hole located at the right side of each of the three
castings (see Fig. 1f) at the bottom of each tripod leg. Tighten the
tripod lock knob only to a “firm feel” to avoid damage to the tripod
caused by overtightening.
ThreadedHole
Leg Lock Knob
l
•
Spread the tripod legs (1) to full extension so that the leg braces
(42) are taut (should one of the tripod leg braces slip out of the
center triangle fastener, merely reposition the brace and slide it
Sliding Inner Leg
Fig. 1f: Tripod lock knob assembly.
back into position). Adjust the tripod with the attached equatorial
mount (2) to the desired height by loosening the tripod lock knobs and extend the sliding inner section
of each tripod leg; then tighten each knob.
•
•
Attach the flexible cable controls (3) and (4). These cable controls are secured in place with a firm
tightening of the thumbscrew located at the end of each cable.
Holding the counterweight (5) firmly in one hand, slip the counterweight onto the counterweight shaft
(6). Attach the counterweight (5) and counterweight shaft (6), by supporting the unlocked (7)
counterweight firmly in one hand, while threading the counterweight shaft into the base of the
Declination axis of the telescope’s equatorial mount with the other (see Fig. 1). Once firmly attached,
slide the counterweight to the midpoint on the counterweight shaft and secure it in place with the lock
knob (7) of the counterweight. Note: If the counterweight ever slips, the secured threaded safety
washer/knob (8) will not let the weight slide entirely off the counterweight shaft. Be certain that this
safety washer/knob is always in place.
•
Release the latitude lock (9) of the equatorial mount, and tilt the polar axis (10) of the telescope to
roughly a 45° angle by turning the latitude adjustment knob (11). With the polar axis thus tilted, firmly
re-tighten the latitude lock.
– 7 –
•
Remove the viewfinder bracket mounting nuts from the viewfinder bracket mounting bolts (16) that
protrude from the optical tube (12), near the focuser (17). Place the viewfinder bracket’s mounting
holes (located at the base of the bracket) over the mounting bolts, so that the bracket is oriented as
shown in Fig. 1. Replace the viewfinder bracket mounting nuts, and tighten to a firm feel. Then center
the viewfinder in both bracket rings by backing off the three thumbscrews (26) on each bracket ring.
Orient the viewfinder so its front objective lens is pointing in the same direction as the open end (front)
of the optical tube (25).
•
•
Position the cradle ring attachment (37) onto the optical tube saddle plate (13), with the mid-point lying
roughly in the center of the saddle plate. Tighten the cradle ring lock knob (36) to a firm feel when the
cradle ring attachment is positioned in the telescope’s saddle (13).
If the cradle ring assmbly did not come already attached to the optical tube assembly (12), loosen the
lock knobs (15) of the cradle rings (14) and open the cradle rings. Place the optical tube assembly
roughly in the center of the cradle rings and close the rings over the tube. Then tighten the cradle ring
lock knobs (15) to a firm feel; do not overtighten these knobs. Please note that you may want to change
the rotational position of the optical tube to gain a more comfortable observing position of the focuser
(17). This adjustment may be performed several times in one observing session, as desired.
•
Insert the H 25mm eyepiece (19) into the focuser, and tighten the focuser thumbscrew (18) to secure
the eyepiece.
The telescope is now fully assembled. Before it can be properly used, however, the telescope must be
balanced and the viewfinder aligned.
Balancing the Telescope
In order for the telescope to move smoothly on its mechanical axes, it must first be balanced about the 2
telescope axes: the polar axis (10, Fig. 1c) and the Declination axis (21, Fig. 1c). All motions of the polar
aligned telescope (more on this later) take place by moving about these two axes, separately or
simultaneously. To obtain a fine balance of the telescope, follow the method below:
•
Loosen the R.A. lock (22, Fig. 1c) and rotate the telescope so that the counterweight shaft (6, Fig. 1c)
is parallel to the ground (horizontal).
•
Slide the counterweight along the counterweight shaft until the telescope remains in one position
without tending to drift down in either direction. Then tighten the counterweight lock knob (7, Fig. 1c),
locking the counterweight in position.
•
Lock the R.A. lock (22, Fig. 1c), and unlock the Declination lock (23, Fig. 1c). The telescope will now
turn freely about the Declination axis. Loosen the cradle ring lock knobs (15, Fig. 1e) so that the main
tube in the cradle rings slides easily up-or-down in the cradle rings. Move the main tube in the cradle
rings until it is balanced rotationally about the Declination axis. Re-lock the knobs (15, Fig. 1e).
The telescope is now properly balanced on both axes.
Alignment of the Viewfinder
The wide field of view provided by the 5 x 24mm viewfinder permits easy object sighting prior to
observation in the higher-power main telescope. The 5 x 24 Viewfinder (24, Fig. 1a) and viewfinder bracket
(20, Fig. 1a) attaches to the telescope tube assembly as described above (see Fig. 1a). In order for the
viewfinder to be functional, however, it must be aligned to the main telescope, so that both the viewfinder
and main telescope point at the same position in the sky. With this simple alignment performed, finding
objects is greatly facilitated, since you will first locate an object in the wide-field viewfinder, then you will
look in the eyepiece of the main telescope for a detailed view. To align the viewfinder follow these steps:
•
•
•
Remove the telescope front dust cover (25, Fig. 1e), and the dust covers of the viewfinder.
Place the low- power (H 25mm) eyepiece into the focuser of the main telescope.
Unlock the R.A. lock (22, Fig. 1c) and the Dec. lock (23, Fig. 1c) so that the telescope turns freely on
both axes. Then point the main telescope at some well-defined land object (e.g. the top of a telephone
pole) at least 200 yards distant, and re-lock the R.A and Dec. axes. Turn the flexible cable controls, (3,
Fig. 1e) and (4, Fig. 1e), to center the object in the telescopic field.
•
With the front of the viewfinder already centered in the front bracket ring, look through the viewfinder
and loosen or tighten, as appropriate, one or more of the rear viewfinder bracket ring thumbscrews
(26, Fig. 1a) until the viewfinder’s crosshairs are likewise centered on the object previously centered
in the main telescope.
– 8 –
•
Check this alignment on a celestial object, such as a bright star or the Moon, and make any
refinements necessary, using the method outlined above.
With this alignment performed, objects first located in the wide-field viewfinder will also be centered in the
main telescope’s field of view. (Note: The viewfinder presents an image which is upside-down.)
UNDERSTANDING CELESTIAL MOVEMENTS AND COORDINATES
Understanding where to locate celestial objects, and how those objects move across the sky is
fundamental to enjoying the hobby of astronomy. Most amateur astronomers adopt the simple practice of
“star-hopping” to locate celestial objects by using star charts or astronomical software which identify bright
stars and star patterns (constellations) that serve as “road maps” and “landmarks” in the sky. These visual
reference points guide amateur astronomers in their search for astronomical objects. And while star-
hopping is the preferred technique, a discussion of using setting circles for locating objects is desirable
since your telescope is provided with this feature. However, be advised, compared to star-hopping, object
location by use of setting circles requires a greater investment in time and patience to achieve a more
precise alignment of the telescope’s polar axis to the celestial pole. For this reason, in part, star-hopping
is popular because it is the faster, easier way to become initiated in the hobby.
Understanding how astronomical objects move: Due to the Earth’s rotation, celestial bodies appear to
move from East to West in a curved path through the skies. The path they follow is known as their line of
Right Ascension (R.A.). The angle of this path they follow is known as their line of Declination (Dec.).
A celestial coordinate system was created that maps an imaginary sphere surrounding the Earth upon
which all stars appear to be placed. This mapping system is similar to the system of latitude and longitude
on Earth surface maps.
In mapping the surface of the Earth, lines of longitude are drawn between the North and South Poles and
lines of latitude are drawn in an East-West direction, parallel to the Earth’s equator. Similarly, imaginary
lines have been drawn to form a latitude and longitude grid for the celestial sphere. These lines are known
as Right Ascension and Declination.
The celestial map also contains two poles and an equator just like a map of the Earth. The poles of this
coordinate system are defined as those two points where the Earth’s North and South poles (i.e., the
Earth's axis), if extended to infinity, would cross the celestial sphere. Thus, the North Celestial Pole (see
Fig. 3) is that point in the sky where an extension of the North Pole intersects the celestial sphere. The
North Star, Polaris, is located very near the North Celestial Pole. The celestial equator is a projection of the
Earth’s equator onto the celestial sphere.
So just as an object's position on the Earth’s surface can be located by its latitude and longitude, celestial
objects may also be located using Right Ascension and Declination. For example: You could locate Los
Angeles, California, by its latitude (+34°) and longitude (118°). Similarly, you could locate the Ring Nebula
(also known as “M57”) by its Right Ascension (18hr) and its Declination (+33°).
I
Right Ascension (R.A.): This celestial version of longitude is measured in units of hours (hr), minutes
(min), and seconds (sec) on a 24-hour "clock" (similar to how Earth's time zones are determined by
longitude lines). The "zero" line was arbitrarily chosen to pass through the constellation Pegasus, a sort
of cosmic Greenwich meridian. R.A.
coordinates range from 0hr 0min
+90° Dec.
North Celestial Pole
(Vicinity of Polaris)
0sec to 23hr 59min 59sec. There are
24 primary lines of R.A., located at
15-degree intervals along the
celestial equator. Objects located
further and further East of the zero
R.A. grid line (0hr 0min 0sec) carry
higher R.A. coordinates.
Star
E
12
11
13
10
14
15
9
8
16
20
17
18
19
7
6
Rotation de la Terre
21
5
4
3
2
22
23
0° Déc.
1
0
Celestial
I
Declination (Dec.): This celestial
version of latitude is measured in
degrees, arc-minutes, and arc-
seconds (e.g., 15° 27' 33"). Dec.
locations North of the celestial
equator are indicated with a plus (+)
sign (e.g., the Dec. of the North
celestial pole is +90°). Dec. locations
E
Ascension droite
Equator
South
Celestial
c.
D.°
-90° Dec.
Pole
Fig. 2: Celestial Sphere.
– 9 –
South of the celestial equator are indicated with a minus (–) sign (e.g., the Dec. of the South celestial
pole is –90°). Any point on the celestial equator (such as the the constellations of Orion, Virgo, and
Aquarius) is said to have a Declination of zero, shown as 0° 0' 0."
With all celestial objects therefore capable of being specified in position by their celestial coordinates of
Right Ascension and Declination, the task of finding objects (in particular, faint objects) in the telescope is
vastly simplified. The setting circles, R.A (27, Fig. 1c) and Dec. (28, Fig. 1c) of the Polaris 114 EQ-DS
telescope may be dialed, in effect, to read the object coordinates and the object found without resorting to
visual location techniques. However, these setting circles may be used to advantage only if the telescope
is first properly aligned with the North Celestial Pole.
LINING UP WITH THE CELESTIAL POLE
Objects in the sky appear to revolve around the celestial pole. (Actually, celestial objects are essentially
“fixed,” and their apparent motion is caused by the Earth’s axial rotation). During any 24 hour period, stars
make one complete revolution about the pole, making concentric circles with the pole at the center. By
lining up the telescope’s polar axis with the North Celestial Pole (or for observers located in Earth’s
Southern Hemisphere with the South Celestial Pole), astronomical objects may be followed, or tracked, by
moving the telescope about one axis, the polar axis.
If the telescope is reasonably well aligned with the pole, therefore, very little use of the telescope’s
Declination flexible cable control is necessary and virtually all of the required telescope tracking will be in
Right Ascension. (If the telescope were perfectly aligned with the pole, no Declination tracking of stellar
objects would be required). For the purposes of casual visual telescopic observations, lining up the
telescope’s polar axis to within a degree or two of the pole is more than sufficient: with this level of pointing
accuracy, the telescope can track accurately by slowly turning the telescope’s R.A. flexible cable control
and keep objects in the telescopic field of view for perhaps 20 to 30 minutes.
To line up the Meade 114 EQ-DS with the pole, follow this procedure:
1. Release the Azimuth lock (30, Fig. 1c) of the Azimuth base (33, Fig. 1c), so that the entire telescope-
with-mounting may be rotated in a horizontal direction. Rotate the telescope until the polar axis (10,
Fig. 1c) points due North. Locate Polaris, the North Star (see Fig. 3), as an accurate reference for due
North.
2. Level the mount, if necessary, by adjusting the
heights of the three tripod legs. Set the Dec dial
LitPtleetDiteipOpeurrse
to 90°.
Polaris
P
3. Determine the latitude of your observing location by
checking a road map or atlas. Release the
latitude lock (9, Fig. 1c) and tilt the telescope
mount with the latitude adjustment knob (11, Fig.
1) so that the pointer indicates the correct latitude
of your viewing location on the latitude scale (29,
Fig. 1c). Re-tighten the latitude lock (9, Fig. 1c).
Big Dipper
Cassiopeia
Cassopée
Fig. 3: Locating Polaris.
4. Without moving the telescope on the Right Ascension and Declination axes, loosen the azimuth and
latitude locks (9 and 30, Fig. 1c) and adjust the telescope until Polaris is centered in the telescope
eyepiece. If steps 1 - 3 above were performed with reasonable accuracy, your telescope is now
sufficiently well-aligned to the North Celestial Pole for visual observations.
Once the mount has been polar-aligned as described above, the latitude angle need not be adjusted again,
unless you move to a different geographical location (i.e. a different latitude). The only polar alignment
procedure that need be done each time you use the telescope is to point the polar axis due North, as
described in step 1 above.
USING THE TELESCOPE
With the telescope assembled, balanced and polar aligned as described above, you are ready to begin
observations. Decide on an easy-to-find object such as the Moon, if it is visible, or a bright star to become
accustomed to the functions and operations of the telescope. For the best results during observations,
follow the suggestions below:
– 10 –
•
•
To center an object in the main telescope, loosen the telescope’s R.A. lock (22, Fig. 1c) and Dec. lock
(23, Fig. 1c). The telescope can now turn freely on its axes. Use the aligned viewfinder to first sight-in
on the object you wish to observe; with the object centered on the viewfinder’s crosshairs, re-tighten the
R.A. and Dec. locks.
If you have purchased an assortment of eyepieces (see Section G on Calculating Power and Section J
on Optional Accessories for higher and lower powers with the telescope), always start an observation
with a low power eyepiece (e.g., the H 25mm eyepiece); get the object well-centered in the field of view
and sharply focused. Then try the next step up in magnification. If the image starts to become fuzzy as
you work into higher magnifications, then back down to a lower power; the atmospheric steadiness is not
sufficient to support high powers at the time you are observing. Keep in mind that a bright, clearly
resolved but smaller image will show far more detail than a dimmer, poorly resolved larger image. The H
25mm eyepiece included with the Meade 114 EQ-DS presents a wide field of view, ideal for general
astronomical observing of star fields, clusters of stars, nebulae, and galaxies; it is also probably the best
eyepiece to use in the initial finding and centering of any object.
•
Once centered, the object can be focused by turning one of the knobs of the focusing mechanism (31,
Fig. 1b). You will notice that the astronomical object in the field of view will begin to slowly move across
the eyepiece field. This motion is caused by the rotation of the Earth on its axis, as described in Section
C, although the planets and stars, are, for practical purposes, fixed in their positions in the sky. The
platform on which the telescope is sitting ( the Earth) rotates once every 24 hours under these objects.
To keep astronomical objects centered in the field of the polar aligned telescope, simply turn the
R.A. flexible cable control (3, Fig. 1e). These objects will appear to move through the field more rapidly
at higher powers. Note that the Declination flexible cable control (4, Fig. 1e) is used only for centering
purposes, and not for tracking.
•
Avoid touching the eyepiece while observing through the telescope. Vibrations resulting from such
contact will cause the image to move. Likewise, avoid observing sites where ground-based vibrations
may resonate the tripod. Viewing from the upper floors of a building may also introduce image
movement.
•
•
You should allow a few minutes to allow your eyes to become “dark adapted” before attempting any
serious astronomical observations. Use a red filtered flashlight to protect your night vision when reading
star maps or inspecting the components of the telescope.
Avoid setting up the telescope inside a room and observing through an open window (or worse yet, a
closed window). Images viewed in such a manner may appear blurred or distorted due to temperature
differences between inside and outside air. Also, it is a good idea to allow your telescope a chance to
reach the ambient (surrounding) outside temperature before starting an observing session.
•
Avoid viewing objects low on the horizon–objects will appear better resolved with far greater contrast
when viewed higher in the sky. Also, if images appear to “shimmer” in the eyepiece–reduce power until
the image steadies. This condition is caused by air turbulence in the upper atmosphere. We repeat the
warning stated at the outset of this manual:
Never point the telescope directly at or near the Sun at any time! Observing the Sun, even for the
smallest fraction of a second, will result in instant and irreversible eye damage, as well as physical
damage to the telescope itself.
The Meade 114 EQ-DS may be used for a lifetime of rewarding astronomical observing, but basic to your
enjoyment of the telescope is a good understanding of the instrument. Read the above instructions carefully
until you understand all of the telescope’s parts and functions. One or two observing sessions will serve to
clarify these points forever in your mind.
The number of fascinating objects visible through your Jupiter reflector is limited only by your own motivation.
Astronomical software, such as Polaris’s AstroSearch, or a good star atlas, will assist you in locating many
interesting celestial objects. These objects include:
•
Cloud belts across the surface of the planet Jupiter.
•
The 4 major satellites of Jupiter, visible in rotation about the planet, with the satellite positions changing
each night.
•
Saturn and its famous ring system, as well as several satellites of Saturn, much fainter than the major
satellites of Jupiter.
– 11 –
•
•
The Moon: A veritable treasury of craters, mountain ranges and fault lines. The best contrast for
viewing the Moon is during its crescent phase. The contrast during the full Moon phase is low due to
the angle of illumination.
Deep-Space: Nebulae, galaxies, multiple star systems, star clusters–hundreds of such objects are
visible through the Meade 114 EQ-DS.
USING SETTING CIRCLES
Setting circles of the polar aligned equatorial mount can facilitate the location of faint celestial objects not
easily found by direct visual observation. To use the setting circles, follow this procedure:
•
Use a star chart or star atlas, and look up the celestial coordinates, Right Ascension and Declination
(R.A. and Dec.), of an easy-to-find bright star that is within the general vicinity of the faint object you
wish to locate.
•
•
Center the determined bright star in the telescope’s field of view.
Manually turn the R.A. setting circle (27, Fig. 1c) to read the R.A. of the object now in the telescope’s
eyepiece.
•
The setting circles are now calibrated (the Dec. setting circle (28, Fig. 1c) is factory calibrated). To
locate a nearby faint object using the setting circles determine the faint object’s celestial coordinates
from a star chart, and move the telescope in R.A. and Declination until the setting circles read the R.A.
and Dec. of the object you are attempting to locate. If the above procedure has been carefully
performed, the faint object will now be in the field of a low power eyepiece.
•
The R.A. Setting Circle must be manually re-calibrated on the current Right Ascension of a star every
time the telescope is set up, and reset to the centered object’s R.A. coordinate before moving to a new
R.A. coordinate setting. The R.A. Setting Circle has two sets of numbers, the inner set is for Southern
hemisphere use while the outer set of numbers (the set closest to the R.A. gear), is for use by
observers located North of the Earth’s equator (e.g., in North America).
CALCULATING POWER
The power, or magnification of the telescope depends on two optical characteristics: the focal length of the
main telescope and the focal length of the eyepiece used during a particular observation. For example, the
focal length of the Meade 114 EQ-DS telescope is fixed at 1000mm. To calculate the power in use with a
particular eyepiece, divide the focal length of the eyepiece into the focal length of the main telescope. For
example, using the H 25mm eyepiece supplied with the Meade 114 EQ-DS, the power is calculated as
follows:
Power = 1000mm ÷ 25mm = 40X
The supplied 3X Barlow lens triples the power of each eyepiece. Insert the 3X Barlow lens into the the
eyepiece holder (17, Fig. 1b), followed by the eyepiece, and secure by tightening the respective
thumbscrews. For example, the 25mm (40X) eyepiece, when used with the 3X Barlow Lens, yields 120X.
The letter “H” refers to the “Hyguens” optical design, which yields corrected images. The optical design has
no bearing on the power of the eyepiece.
Meade Instruments manufactures several types of eyepiece designs that are available for your telescope.
The type of eyepiece (“MA” Modified Achromatic, “SP” Super Plössl, etc.) has no bearing on magnifying
power but does affect such optical characteristics as field of view, flatness of field, eye relief, and color
correction.
The maximum practical magnification is determined by the nature of the object being observed and, most
importantly, by the prevailing atmospheric conditions. Under very steady atmospheric “seeing,” the Meade
114 EQ-DS may be used at powers up to about 225x on astronomical objects. Generally, however, lower
powers of perhaps 75x to 175x will present the best images consistent with high image resolution. When
unsteady air conditions prevail (as witnessed by rapid “twinkling” of the stars), extremely high-power
eyepieces result in poor magnification, where the object detail observed is actually reduced by the
excessive power.
– 12 –
MAINTENANCE
Cleaning
As with any quality instrument, lens or mirror surfaces should be cleaned as infrequently as possible. Front
surface aluminized mirrors, in particular, should be cleaned only when absolutely necessary. In all cases
avoid touching any mirror surface. A little dust on the surface of a mirror or lens causes negligible loss of
performance and should not be considered reason to clean the surface. When lens or mirror cleaning does
become necessary, use a camel’s hair brush or compressed air gently to remove dust. If the telescope’s
dust cover is replaced after each observing session, cleaning of the optics will rarely be required.
Mount and Tripod Adjustments
Every Meade 114 EQ-DS equatorial mount and tripod is factory inspected for proper fit and function prior
to shipment.
The tripod legs have wingnuts (39, Fig. 1c), and Phillips-head screws (38, Fig. 1c) that may have backed
off. They may be tightened to a firm feel for a more sturdy performance of the telescope.
Collimation (Alignment) of the Optics
All Meade 114 EQ-DS telescopes are optically aligned at the factory prior to shipment. It is unlikely that you
will need to align, or collimate, the optics after receipt of the instrument. However, if the telescope received
unusually rough handling in shipment, it is possible that the optics must be re aligned for best optical
performance. In any case this alignment procedure is simple, and requires only a few minutes the very first
time the telescope is used. Take the time to familiarize yourself with the following collimation procedure, so
that you will recognize a properly collimated instrument and can adjust the collimation yourself, if
necessary.
a. Correct collimation
The properly collimated (aligned) mirror system in the Meade 114 EQ-DS assures the sharpest images
possible. This occurs when the primary mirror and diagonal mirror are tilted so that the focused image (see
Fig. 4) falls directly through the center of the focuser drawtube (17, Fig. 1b). These mirror tilt adjustments
are made with the diagonal assembly (Fig. 5) and the primary mirror cell (Fig. 6), and will be discussed
later.
To inspect the view of the mirror collimation, look down the focuser drawtube with the eyepiece removed.
The edge of the focuser drawtube (1, Fig. 7), will frame the reflections of the primary mirror with the 3 mirror
clips (2, Fig. 7), the diagonal mirror (3, Fig. 7) , the spider vanes (4, Fig. 7), and your eye (5, Fig. 7).
Properly aligned, all of these reflections will appear concentric (i.e., centered) as illustrated in Fig. 7.
Any deviation from the concentric reflections will require adjustments to the diagonal assembly (Fig. 5),
and/or the primary mirror cell (Fig. 6).
b. Diagonal holder adjustments
If the diagonal mirror (1, Fig. 8) is centered in the drawtube (2, Fig. 8), but the primary mirror is only partially
visible in the reflection (3, Fig. 8), the 3 Phillips-head diagonal tilt screws (1, Fig. 5). Note: To adjust these
screws you must first remove an adhesive backing) must be unthreaded slightly to the point of where you
can tilt the diagonal holder (3, Fig. 5) from side-to-side by grasping the diagonal holder with your hand and
tilt until you see the primary mirror become as centered in the reflection of the diagonal mirror as possible.
Once you are at the best position, thread in the 3 Phillips-head diagonal tilt screws to lock the rotational
Diagonal
Assembly
Primary Mirror
Diagonal Mirror
is Diclis
Promary Mirror-Tilt
Screws
Focused Image
I
Fig. 4: The Newtonian Reflecting Telescope.
– 13 –
position. Then, if necessary, make adjustments to these 3 Phillips-head
screws to refine the tilt-angle of the diagonal mirror until the entire primary
mirror can be seen centered within the diagonal mirror reflection. When the
diagonal mirror is correctly aligned, it will look like Fig. 9. (Note: the primary
mirror is shown out of alignment.)
Remove
adhesive
backing
1
c. Primary mirror adjustments
If the diagonal mirror (1, Fig. 9) and the reflection of the primary mirror (2,
Fig. 9) appear centered within the drawtube (3, Fig. 9), but the reflection of
your eye and the reflection of the diagonal mirror (4, Fig. 9) appear off-
center, you will need to adjust the primary mirror tilt Phillips-head screws of
Fig. 5: Diagonal Assembly.
the primary mirror cell (3, Fig. 6). These primary tilt screws are located behind the primary mirror, at the
lower end of the main tube. See Fig. 4. To adjust the primary mirror tilt screws, first unscrew several turns,
the 3 hex-head primary mirror cell locking screws (2, Fig.6) that are next to each primary mirror tilt Phillips-
head screw. Then by trial-and-error, turn the primary mirror tilt Phillips-head screws (3, Fig. 6) until you
develop a feel for which way to turn each screw to center the reflection of your eye. Once centered, as in
Fig. 7, turn the 3 hex-head primary mirror cell locking screws (2, Fig. 6) to relock the tilt-angle adjustment.
d. Star testing the collimation
With the collimation performed, you will want to test the accuracy of the alignment on a star. Use the H
25mm eyepiece and point the telescope at a moderately bright (second or third magnitude) star, then
center the star image in the telescope’s field-of-view. With the star centered follow the method below:
•
Bring the star image slowly out of focus until one or more rings are visible around the central disc. If
the collimation was performed correctly, the central star disk and rings will be concentric circles, with a
dark spot dead center within the out-of-focus star disk (this is the shadow of the secondary mirror), as
shown in Fig. 10C. (An improperly aligned telescope will reveal elongated circles (Fig. 10A), with an
off-center dark shadow.)
•
•
•
•
If the out-of-focus star disk appears elongated (Fig. 10A), you will need to adjust the primary mirror
Phillips-head tilt screws of the primary mirror cell (3, Fig. 6).
To adjust the primary mirror tilt screws (3, Fig. 6), first unscrew several turns the 3 hex-head primary
mirror cell locking screws (2, Fig. 6), to allow free turning movement of the tilt knobs.
Using the flexible cable controls (3 and 4, Fig. 1e), move the telescope until the star image is at
the edge of the field-of-view in the eyepiece, as in Fig. 10B.
As you make adjustments to the primary mirror tilt screws (3, Fig. 6), you will notice that the out-of-
focus star disk image will move across the eyepiece field. Choose one of the 3 primary mirror tilt screws
and slightly move the shadow to the center of the disk. Then slightly move the telescope using the
flexible cable controls to center the star disk image in the center of the eyepiece.
•
•
If any further adjustments are necessary, repeat this process as many times as needed until the out-
of-focus star disk appears as in Fig. 10C, when the star disk image is in the center of the eyepiece
field.
With the star testing of the collimation complete, tighten the 3 hex-head primary mirror locking screws
(2, Fig. 6).
2
3
Fig. 6: Primary Mirror Cell.
– 14 –
1
1
2
3
2
3
4
2
5
Fig. 7: Correct Collimation.
Fig. 8: Diagonal Mirror Misalignment.
1
2
3
4
Fig. 9: Primary Mirror Misalignment.
A
B
C
Fig. 10: Collimation.
– 15 –
SPECIFICATIONS
Primary (main) mirror focal length: . . . . . .1000mm
Primary mirror diameter: . . . . . . . . . . . . . .4.5" (114mm)
Focal ratio: . . . . . . . . . . . . . . . . . . . . . . . .f/8
Mounting: . . . . . . . . . . . . . . . . . . . . . . . . .German equatorial
OPTIONAL ACCESSORIES
See your Meade 114 EQ-DS dealer for further details on any of these accessories.
Additional Eyepieces (.965"): Meade recommends the following eyepieces for enhanced
astronomical and/or terrestrial viewing:
• MA 9mm (.965"): Provides high quality, higher power, close-up observation of the Moon and planets
(100x).
• MA 40mm (.965"): Offers the most dramatic, wide field of view for observing deep-space objects. This
is also the eyepiece most recommended for viewing of objects on land (23x).
Basic Camera Adapter (.965” O.D.): Permits direct attachment of 35mm SLR cameras to the
telescope. (Requires T-Mount for your specific brand of camera). Suitable for lunar disk and land
photography.
AMDeVaA dN CeE IDnstruments Corporation
World’s Leading Manufacturer of Astronomical Telescopes for the Serious Amateur
6001 Oak Canyon, Irvine, California 92618 I (949) 451-1450
P R O D U C T S D I V I S I O N
ver 7/03
© 2003
|