Specifications
Capacity:
500 Lbs. Maximum
27‑1/4”
Maximum Table Height:
1/4-TON CAPACITY
HYDRAULIC
Minimum Table Height
Table Size
9”
27‑3/4” x 17‑5/8”
Steel Construction
27‑ 3/4”
Construction:
Table Length:
Weight
LIFT TABLE
95.7 lbs.
94822 Hydraulic Lift Table
Unpacking
INsTRUCTIONs AND PRECAUTIONs
Note: When unpacking, use assistance when lifting the Hydraulic
Lift Table from the box. Or set the packaging box sideways
and slide the Lift Table out from the box sideways.
Caution: When lifting Hydraulic Lift Table from packaging
box, be sure to grip the main frame. Do not just grip
the Table. Doing so will only raise up the Table and
keep the unit’s frame in the packaging box.
Important safety Information
1. Do not exceed 1/4 ton (500 lb.) max weight capacity.
Be aware of dynamic loading! Sudden load movement
may briefly create excess load causing product failure.
2. Use only on flat, level and hard surface capable of
supporting the Lift Table and any item(s) placed on
Table. Evenly distribute load on Table to avoid tipping.
Visit our website at:
3. Use as intended only. Do not use Lift Table to
lift or transport animals, pets, or people.
4. Assemble only according to these instructions.
Improper assembly can create hazards.
5. Follow all hydraulic bleeding instructions
Read this material before
using this product.
specified in this manual.
6. Wear ANSI‑approved safety goggles and heavy‑
duty work gloves during assembly and use.
Failure to do so can result
in serious injury.
sAVE THIs mANUAL.
7. Keep assembly area clean and well lit.
8. Keep bystanders out of the area during assembly.
When unpacking, make sure
that the product is intact and
undamaged.
9. Do not assemble when tired or when under
the influence of drugs or medication.
If any parts are missing or broken,
please call 1‑800‑444‑3353
as soon as possible.
10. This product is not a toy. Do not allow
children to play with or near this item.
11. Use as intended only.
©
®
Copyright 2010 by Harbor Freight Tools . All rights reserved. No
portion of this document or any artwork contained herein may be
reproduced in any shape or form without the express written consent
of Harbor Freight Tools. Diagrams within this document may not
be drawn proportionally. Due to continuing improvements, actual
product may differ slightly from the product described herein. Tools
required for assembly and service may not be included.
12. Inspect before every use; do not use
if parts are loose or damaged.
13. Maintain product labels and nameplates. These carry
important safety information. If unreadable or missing,
contact Harbor Freight Tools for a replacement.
For technical questions or replacement
parts, please call 1-800-444-3353.
Manual Revised 11a
Operating Instructions
Bleeding Instructions
1. Before loading and while stationary, lock the back
Casters (19) to prevent the Lift Table from moving.
If the Lift Table is not performing properly, it may
be due to air in the hydraulic system. Follow
these steps to bleed air from the system.
2. The Table (1) is raised by pumping the Lifting Pedal
(27) with your foot until the desired height is achieved.
1. Raise the Table to it’s highest position.
3. Once desired height is reached, swing down the
Safety Bars (7) on either side of the Lift Frame. This
will prevent any kind of uncontrolled Table drop.
2. Swing down the two Safety Bars so that they both
rest on the top platform of the Base Assembly.
3. Remove the rubber Oil Plug (J04). You can carefully
4. To lower the Table, Squeeze the Release
Handle (22) at the top of the main Handle.
remove it with a large flat head screwdriver.
4. After the Oil Plug is removed, swing the two
Safety Bars back against their stops.
Note: Be sure to lift Safety Bars up, allowing the
Table to be completely lowered (if needed).
5. Squeeze the Release Handle to lower the Table. This
should purge the air out of the hydraulic system.
6. Raise the Table to it’s highest position and swing both
the Safety Bars down onto the Base Assembly (17).
maintenance
7. Top off hydraulic fluid into the oil hole where the Oil Plug
1. Lubricate hydraulic connections monthly
with a good quality grease.
goes until it is full. Note: make sure you use new oil.
8. Replace the Oil Plug by firmly
2. Check for the free movement and wear
of the wheels. Replace if needed.
pressing it in while twisting it.
3. Check the Caster brakes regularly. They
should lock firmly and release completely.
4. If you encounter difficulty using the Release
Handle to lower the Table, the Control
Cable (49) may need adjusting.
WARNING! Make sure the Release Handle is pressed
only halfway down during adjustment. This will allow
the Table to lower slowly for safety purposes.
a. With assistance, tip over Lift Table.
Hex Bolt (16)
Control Cable (49)
Cable Bolt (50)
Figure 5
b. Loosen the Cable Bolt (50) and Cable Nut
(51) and tug the Control Cable until it is tight.
WARNING! Do not pull too tight; you want to
leave a small amount of give. See Figure 5.
c. Re‑fasten the Nut and Bolt. Then test the
Release Handle, making sure the Release
Handle is pressed halfway down.
5. Check for oil leakage from the hydraulic cylinder.
The hydraulic cylinder is not user serviceable.
WARNING! Any service or repairs to the Hydraulic
Lift Table should be performed by a qualified
service technician. Improper repairs or service
could result in equipment failure or personal injury.
SKU 94822
For technical questions, please call 1-800-444-3353.
Page 3
Lift Table Parts List
Part
1
2
Description
Toptable
Lift Frame
Shaft
Qty
1
1
Part
Description
Qty
2
2
Part
38 Spring Cap
39 Spring
Description
Qty
1
1
19 Caster Ass'y
20 Bolt M8 x 30
21 Handle
3
2
1
40 Spring
1
4
5
6
Retaining Ring
Pin (1)
Bolt
8
2
2
22 Brake Handle
23 Bolt M8 x 25
24 Pin
1
2
1
41 Bolt
42a Release Valve Link
44 R‑pin
1
1
1
7
8
9
Safety Bar
Nut
Pin
2
2
2
1
25 Bolt Sleeve
26 Brake Thread
27 Lifting Pedal
28 Bumper
1
1
1
1
45 Pin (7)
46a Pump
47 Front Wheel
48 Wheel Bushing
(not shown)
1
1
2
2
10 Pin (2)
11 Pin (3)
2
29 Bolt
1
12 Nut M8
12
8
2
14
2
1
30a Lifting Pedal Connector
31 Pin (4)
33a Connecting Plate
34a Cotter
35 Pin (5)
36 Pin (6)
1
1
1
2
1
1
2
49 Control Cable
(not shown)
50 Cable Bolt (not shown)
51 Cable Nut (not shown)
52 Washer
1
13 Lock Washer
14 Lock Nut
15 Washer
16 Hex Bolt M8 x 60
17 Base Ass'y
18 Bolt M8 x 16
1
1
1
1
53 Retaining Ring
8
37 Retaining Ring
Record serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.
PLEAsE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAgRAM
IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISINg OUT OF HIS OR HER REPAIRS TO THE ORIgINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISINg OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Page 4
For technical questions, please call 1-800-444-3353.
SKU 94822
Lift Table Assembly Diagram
53
30a
33a
34a
52
34a
46a
42a
SKU 94822
For technical questions, please call 1-800-444-3353.
Page 5
Pump Parts List and Diagram
Part
J01 O‑ring
Description
Qty
1
1
1
1
Part
Description
Qty
1
1
1
1
Part
J31 O‑ring
J32 Seal Ring
J33 O‑ring
J34 Damp Valve Seat
J35 Spring
Description
Qty
1
1
1
1
J16 Nylon Ring
J17 Oil Filter
J18 Spring
J19 Ball
J20 Ball Cup
J21 Spring
J02 Top Nut
J03 Nylon Ring
J04 Oil Plug
J05 Reservoir
J06 Ram
1
1
1
1
1
1
J36 O‑ring
J07 Cup Seal
J08 O‑ring
1
1
J22 Screw
J23 O‑ring
1
1
J37 Damp Valve Rod
J38 Screw
1
1
J09 Screw
2
J24 Screw
1
J39 Pump
1
J10 Packing Washer
J11 Spring
J12 Ball
J13 Oil Filter
J14 Cylinder
J15 Washer
2
1
2
1
1
1
J25 Plastic Cap
J26 Spring Collar
J27 Oil Filter
J28 Valve Plug
J29 Spring
1
2
1
1
1
1
J40 Copper Washer
J41 Pump Cylinder
J42 Seal Ring
J43 Seal Ring
J44 Pump Piston
1
1
1
1
1
J30 Ball
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
Page 6
For technical questions, please call 1-800-444-3353.
SKU 94822
LImITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability
standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship
for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity,
improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use
of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS ExPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, ExPRESS OR IMPLIED, INCLUDINg THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If
our inspection verifies the defect, we will either repair or replace the product at our election or we may elect
to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return
repaired products at our expense, but if we determine there is no defect, or that the defect resulted from
causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 94822
For technical questions, please call 1-800-444-3353.
Page 7
|