INSTALLATION INSTRUCTIONS FOR PART 95-7325
APPLICATIONS
Hyundai Santa Fe
2007-10
(excludes 2010 NAV models)
95-7325
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Units Provision
KIT COMPONENTS
A) Double DIN Trim Plate B) Double DIN Brackets
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• 70-7302 - Hyundai Harness 2007-up
• 70-7305 - Hyundai / KiA Harness 2009
Antenna Adapter:
A
B
• 40-KI11 - 2009-10 Santa Fe Adapter
TOOLS REQUIRED:
Small Flat Blade Screwdriver • Panel Removal Tool
• Phillips Screwdriver
1-800-221-0932
© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
95-7325 DASH DISASSEMBLY
HYUNDAI SANTA FE 2007-10
A
1
2
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
Remove (1) Phillips screw from the
right side of the panel below the
steering column then unclip and let
right side of panel hang. (Figure A)
Unclip and remove the cover above
the clock on top of panel surrounding
the radio. (Figure B)
3
4
Unclip and remove the panel extend-
ing across the dash below the a/c
control and above the glove box
including the ash tray. (Figure C)
B
5
6
Remove (2) Phillips screws then
unclip and remove the panel sur-
rounding the radio including the a/c
vents. (Figure D)
Remove (4) Phillips screws securing
the radio. Unplug and remove radio.
Continue to kit assembly.
D
C
1
95-7325 KIT ASSEMBLY
DOUBLE DIN RADIO PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
Snap the Double DIN brackets to the
outside edge of the Double DIN trim
plate. (Figure A)
1
2
Slide the Double DIN radio into the
bracket/trim plate assembly and
secure the radio to the assembly using
the screws supplied with the radio.
(Figure B)
Continue to final assembly.
B
2
95-7325 KIT ASSEMBLY
STACKED ISO UNITS PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
Snap the Double DIN brackets to the
outside edge of the Double DIN trim
plate. (Figure A)
1
2
Slide the stacked ISO units into the
bracket/trim plate assembly and
secure the units to the assembly using
the screws supplied with the units.
(Figure B)
Continue to final assembly.
B
3
95-7325 FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
Right Front (+) . . . . . . . . . . . . Gray
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
4
95-7325
NOTES
5
95-7325 INSTRUCTIONS
1-800-221-0932
REV. 04/27/10 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
INST95-7325
|