KIT FEATURES
Shaft and
DIN unit
provisions
99-3009
INSTALLATION
INSTRUCTIONS
KIT COMPONENTS
Radio Housing
APPLICATIONS
CAR
CHEVROLET
PAGE
Camaro 1993-96..........................................................1
PONTIAC
Spacer
Bonneville 1994-99......................................................1
Firebird 1993...............................................................4
Firebird 1994-02........................................................ 5
Grand Am 1996-98......................................................2
Grand Am 1999-00..................................................... 2
Grand Prix 1994-96.....................................................3
Grand Prix 1997-02.....................................................3
Sunfire 1995-99.......................................................... 4
Trans Am 1993.............................................................4
Trans Am 1994-02....................................................... 5
(1) Keps Nut
(1) Phillips
Pan-head Screw
(1) Carriage Bolt
TOOLS REQUIRED
Phillips screwdriver
Cutting tool
© COPYRIGHT 2001 METRA ELECTRONICS CORPORATION
Socket wrench
rev. 090103
PONTIAC Trans Am / Firebird 1994-02
PONTIAC Grand Am 1996-98
1
1
2
2
"C"
"C"
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unclip
the radio trim bezel. Remove (4) 7mm hex-
head screws securing the factory head unit
anddisconnectthewiring.
Cut and remove all mounting tabs on the
Radio Housing EXCEPT tabs "C". The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #5.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(2) Phillips screws from the pocket. Remove
(2) Phillips screws above the instrument
cluster. Unclip the dash trim bezel and
Cut and remove all mounting tabs on the
Radio Housing EXCEPT tabs "C". The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #5.
remove.
Remove (3) 7mm hex-head
screws securing the factory head unit and
disconnectthewiring.
ALL VEHICLES
PONTIAC Grand Am 1999-00
3
Fig.
1
2
*OPTIONAL
Illustration not
available when
printed
Fig. B
"C"
2-SHAFT HEAD UNITS: Slide the aftermarket head unit into the kit and secure with shaft
nuts. (seeFig. A)
Cut and remove all mounting tabs on the
Radio Housing EXCEPT tabs "C". The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #5.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unclip
the radio trim bezel. Remove (3) 9/32"
screws securing the factory head unit and
disconnectthewiring.
DIN HEAD UNITS: Insert the Spacer* into the Radio Housing. Slide the DIN cage into the kit
and secure by bending the metal locking tabs down. Slide the aftermarket head unit into the
cage until secure. (see Fig. B)
5
2
PONTIAC Grand Prix 1994-02
PONTIAC Sunfire 1995-99
1
2
1
2
"C"
Fig. A
"C"
Disconnect the negative battery terminal to
prevent an accidental short circuit. Using a
small set of pliers, grasp the retaining clip on
the back of the gear shifter handle and
remove the clip. Remove the gear shifter
handle. Unclip the center console and
Cut and remove all mounting tabs on the
Radio Housing EXCEPT tabs "C". The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #5.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Open
the glove box and remove (2) Phillips screws
exposed on the right edge of the radio trim
Fig. B
bezel.
Unclip the bezel and remove.
Cut and remove all mounting tabs on the
Radio Housing EXCEPT tabs "C". (see
Fig. A). Using a dremel tool, cut and remove
the shaded portions of the sub-dash plastic.
This will provide the necessary depth for
installation. (see Fig. B). Skip to the
Installation Instructions for ALL VEHICLES
on Page #5.
Remove (2) 7mm hex-head screws securing
the factory head unit and disconnect the
wiring.
remove.
Remove (2) 7mm hex-head
screws exposed under the climate controls.
Unclip the radio trim bezel and remove.
Remove (2) 7mm hex-head screws securing
the factory head unit and disconnect the
wiring.
PONTIAC Trans Am / Firebird 1993
PONTIAC Grand Prix 1997-99
1
2
1
2
"B"
"C"
Cut and remove all mounting tabs on the
Radio Housing EXCEPT tabs "B". The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #5.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unclip
the radio trim bezel. Remove (4) 7mm hex-
head screws securing the factory head unit
anddisconnectthewiring.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unclip
the entire dash trim bezel. Remove the
screws securing the factory head unit and
disconnectthewiring.
Cut and remove all mounting tabs on the
Radio Housing EXCEPT tabs "C". The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #5.
3
4
|