INSTALLATION INSTRUCTIONS FOR PART 95-7419
APPLICATIONS
Nissan Altima
2005-2006
(Without factory navigation)
95-7419
KIT FEATURES
• Double DIN Head Unit Provision
• Stacked ISO DIN Head Unit Provision
KIT COMPONENTS
• ( A) DDIN Trim plate
A
TOOLS REQUIRED:
Phillips Screwdriver • Small Flat Blade Screwdriver
1-800-221-0932
© COPYRIGHT 2004-08 METRA ELECTRONICS CORPORATION
DASH DISASSEMBLY
95-7419
2005-06 NISSAN ALTIMA
A
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
2
Unclip and remove the trim panel
surrounding the climate controls.
(Figure A)
Remove (4) Phillips screws securing
climate control and remove.
(Figure B)
3
4
B
Unclip and remove the panel sur-
rounding radio including A/C vents.
(Figure C)
Remove (4) Phillips screws securing
5
radio to remove. (Figure D)
C
D
1
KIT ASSEMBLY
95-7419
2005-06 NISSAN ALTIMA
DOUBLE DIN HEAD UNIT PROVISION
A
Snap the 95-7419 trim plate into the
radio trim panel. (Figure A)
1
2
Slide the DDIN radio unit into the
factory brackets and secure the unit
to the brackets using the screws
supplied with the head unit.
(Figure B)
Install the 95-7419 Trim Plate
from Rear
B
2
KIT ASSEMBLY
95-7419
2005-06 NISSAN ALTIMA
STACKED ISO DIN HEAD UNIT PROVISION
A
Snap the 95-7419 trim plate into the
radio trim panel. (Figure A)
1
2
Slide the stacked ISO DIN units into
the factory brackets and secure the
units to the brackets using the
screws supplied with the head units.
(Figure B)
Install the 95-7419 Trim Plate
from Rear
B
3
FINAL ASSEMBLY
95-7419
FINAL ASSEMBLY
A
B
A)
B)
C)
D)
Strip wire ends back 1/2"
Twist ends together
Solder
Tape
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown.
(Isolate and individually tape off the ends of any unused wires to prevent
electrical short circuit.)
1
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc . . . Red
Right Front (+) . . . . . Gray
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Right Front (-). . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-). . . . . . . White / Black
Right Rear (+). . . . . . Violet
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
4
95-7419
NOTES
5
95-7419
1-800-221-0932
REV 03-03-08 © COPYRIGHT 2004-08 METRA ELECTRONICS CORPORATION INST95-7419
|