WR-300 Owner’s Manual
Table of Contents
Quick Start Guide
2
Table of Contents
3
Product Information
4
WR-300 Controls
5
Icons on the Display
5
WR-300 Accessory Jacks
Set the Time
5
6
Set the Date
6
Set the ALARM Time
6
Choosing an Alarm Type
Programming Notes
6
7
Getting your S.A.M.E. County Codes
Programming S.A.M.E. County Codes
Helpful Tip
7
8
8
All S.A.M.E. County Code
A Single S.A.M.E. County Code
Multiple S.A.M.E. County Code
Reviewing Stored S.A.M.E. Codes
Choosing an Alert Type(Voice or Siren)
To Turn the Alert ON and OFF
Setting the Alert Volume
Selectable Alert Option
Testing the Alert
8
8
8
9
9
9
9
9
10
10
10
10
11
11
11
11
12
13
14
15
16
16
17
18
19
Reviewing the Alert
Test Signals Broadcast by NWS
No Reception Warning
AM/FM Radio
Turning the AM/FM Radio On
Changing the AM/FM Stations
AM/FM Memory Channels
Troubleshooting
Reception
About NOAA,NWS,&S.A.M.E.County Codes
S.A.M.E. County Code Record
Specification
FCC Compliance Specification
Warranty Info
Service
Other Midland Products
Page 3
WR-300 Owner’s Manual
Product Information:
Thank you for choosing Midland! Your new WR-300 weather radio is the latest in weather
and hazard alert monitoring technology, providing you with the information needed to keep you
safe. Your WR-300 weather radio has a special receiver that tunes to the 24/7 broadcast issued
by the National Weather Service. The combined All Hazards/Weather Alert broadcast network is
the single, most immediate source for comprehensive weather and emergency information avail-
able to the public.
This WR-300 weather radio has an innovative automatic alert system. In the event of a
special warning broadcast, the radio is automatically activated along with a loud tone, a flashing
LED indicator and an “alert” message on the LCD. Emergency weather bulletins include alerts
about: tornadoes, hurricanes, floods, ice/snow storms and other severe weather. Other emer-
gencies might include: Amber alert, hazardous explosions, fires, chemical spills and other civil
emergencies.
In addition, this WR-300 weather radio has the “S.A.M.E. Digital Weather/Hazard Alert”
feature, providing you with constant monitoring of your localized NWS broadcast. The S.A.M.E.
decoding receiver allows you to hear only messages for the area(s) concerning you. You now
have a choice as to what information will be brought to you.
We encourage you to read this owner’s manual thoroughly before operating this
radio. This manual is a valuable part of your new weather radio. See the “Quick Start
Instructions” section of this manual for the initial weather radio setup and programming.
After your new weather radio is programmed and operating properly, store the manual in
a safe place for future reference.
Page 4
WR-300 Owner’s Manual
WR-300 Controls:
Weather/ Hazard
On/OFF Button
AM/FM
Button
Alert
On/OFF
Snooze
Radio Button
Warning Light-
Red
Alarm Clock
On/Off Switch
Watch Light-
Orange
Programming
(Arrow)
Buttons
Advisory
Light- Yellow
Power On/Off
and Volume
Select Button
Menu Button
ICONS on the Display
Alphanumeric
Message
Time Indicator
Clock Alarm
County Code
Indicator
Weather
Channel
Indicator
Alert Type
Indicator
Low Battery
indicator
LCD Backlighting
Press and release any button to turn the backlight on for 5 seconds. For continuous backlight,
press the “MENU” button, then the press the “DOWN” arrow until “LIGHT” displays on the
screen. Then press the “SELECT” button. Then press the “UP” arrow to change the backlight
setting from “NORMAL” to “CONTINUOUS”. Press the “SELECT” button to save your settings.
WR-300 Accessory Jacks
External
Antenna
DC Jack
Connector
Programming
Cable Port
Earphone
Jack
External
Alert Jack
Page 5
WR-300 Owner’s Manual
Setting the AM /FM Clock Radio Functions:
Set the Time:
(A). Turn on the weather radio with power/volume wheel on side of the radio.
(B). Press the “MENU” button.
(C). Press the “DOWN” arrow button until “SET UP TIME” is displayed.
(D). Press the “SELECT” button, hour setting will begin to flash.
(E). Press the “UP” button to adjust the hour setting. (Note: the am/ pm setting cannot be
manually changed; it changes automatically as you scroll through the hours.)
(F). Press the “RIGHT” arrow to adjust minutes and save your hour setting.
(G). Press the “UP” button to adjust the minute setting.
(H). Press the “SELECT” button to store the time setting.
(I). Press the “MENU” button to return to the main menu.
Set the DATE:
(A). Turn on the weather radio with power/volume wheel on side of the radio.
(B). Press the “MENU” button.
(C). Press the “DOWN” arrow until “SET UP DATE” is displayed.
(D). Press the “SELECT” button.
(E). Press the “UP” arrow to adjust the day.
(F). Press the “RIGHT” arrow to select the month.
(G). Press the “UP” arrow to adjust the month.
(H). Press the “RIGHT” arrow to select the year.
(I). Press the “UP” arrow to adjust the Year.
(J). Press the “SELECT” button to store DAY/MONTH/YEAR.
K). Press the “MENU” button to return to the main menu.
Set the ALARM Time (for the AM/FM Clock Radio)
(A). Turn on the weather radio with power/volume wheel on side of the radio.
(B). Press the “MENU” button.
(C). Press the “DOWN” arrow until “SET UP ALARM” is displayed .
(D). Press the “SELECT” button. The alarm hour setting will begin to flash.
(E). Press the “UP” arrow to adjust the alarm hour setting. (Note: the AM/ PM setting
cannot be manually changed; it changes automatically as you scroll through the hours.)
(F). Press the “RIGHT” arrow to choose setting alarm minutes.
(G). Press the “UP” arrow to adjust the alarm minute setting.
To Choose the Type of Alarm:
(A). Press the “MENU” button.
(B). Use the “UP” arrow to choose radio or sound for clock alarm. (The icons are
located below the clock display.)
(C). Press the “SELECT” button to store the type of alarm setting.
(D). To activate the alarm, set the “ALARM OFF/ON” switch to the “ON” position.
The clock face icon will appear.
(E). The “SNOOZE” button on the top of the WR-300 is for advancing the alarm time
by 9 minutes each time the alarm sounds. The “SNZ” icon will be displayed.
(F). Turn the alarm off with the ”ALARM OFF/ON” switch on side of the radio.
(G). Press the “UP” arrow to adjust the alarm minute setting.
Page 6
WR-300 Owner’s Manual
Programming Notes:
*Your WR-300 can be programmed with up to 23 different S.A.M.E. codes for your county and
the surrounding counties of your choice. This ensures you receive alerts for only those counties
concerning you.
* Please note: Embedded in an alert message is the amount of time for which the alert is active.
The WR-300 will continue to display the alert until the expiration time. Ex: END 12-55P indicates
the event ends at 12:55 PM.
Getting your S.A.M.E. County Codes:
A. First, determine the counties you are interested in. Then, do one of the following
three steps to get the codes:
1. The National Weather Service Toll-Free Number provides S.A.M.E. County
Codes at:1-888-NWS-S.A.M.E. (1-888-697-7263)
This is what to expect when you call the NWS number. When you call the NWS
toll-free number, automated instructions will guide you to the S.A.M.E. County
Code(s) you need. The number will be six digits long.
•You will hear “Welcome to the National Weather Service. You have reached
the Specific Area Message Encoding Program Service.”
• If you select “touch tone” to make your entries, you will be prompted to enter
the name of your state using the telphone keypad.
• Next you will be prompted to enter your county name.
• Then you will hear, “Your geographic code is XXXXXX”. (This is your
S.A.M.E. County Code.
2. The Internet Web Site of National Weather Service-
When you pull up this URL, you will see a list of states .
• Click on your state.
• Find your county, and record the S.A.M.E. number listed next to your county.
• Click on the weather radio link at the top of the page.
• At the top of the weather radio page will be a link to the NWS list of states
and corresponding county codes. Click on this link.
• Click on your state and a list of counties and codes will be listed. Find your
county and then find your code.
Page 7
WR-300 Owner’s Manual
Programming S.A.M.E. County Codes into the WR-300
Helpful Tip: The S.A.M.E. code is created using the following method:
• The first digit is the subcounty code-currently 0 in most areas.
• The second two digits represent the state code.
• The last three digits represent the county code.
“ALL” S.A.M.E. County Codes is the Factory Setting:
Your WR-300 weather radio is preprogrammed to receive NWS weather and hazard alert trans-
missions for all S.A.M.E. county codes within range. If this is what you want, leave the radio set
to “ALL”.
A Single S.A.M.E. County Code:
• Press the “MENU” button to open menu options.
• Press the “UP” arrow to scroll through menu options until “County Code” is
displayed.
• Press the “SELECT” button and then the “UP” arrow to scroll through ”SINGLE”, “MUL-
TIPLE” or “ALL”.
• Display “SINGLE”, then press the “SELECT” button.
• “Code 01” will be displayed. Press the “SELECT” button to program this code. The first
digit space will start blinking.
• Use the “UP” arrow to scroll through the digits 0-9. Input the first digit then
press the “RIGHT” arrow to save that selection and move to the next digit.
• Continue programming all 6 digits in this way. When finished, press the “SELECT” button
and your entered code will be saved.
Multiple S.A.M.E. County Codes:
• Press the “MENU” button to open menu options.
• Press the “UP” arrow to scroll through menu options until “County Code” is
displayed.
• Press the “SELECT” button and then the “UP” arrow to scroll through “SINGLE”, “MUL-
TIPLE” or “ALL”.
• Display “MULTIPLE”, then press “SELECT”.
• Use the “UP” arrow to scroll through code locations 1-23. You are able to
program up to 23 different county codes into your WR-300 weather radio.
• Display the location you want then press the “SELECT” button. The first
digit space will start blinking.
• Use the “UP” arrow to scroll through the digits 0-9. Input the first digit then
press the “RIGHT” arrow to save that selection and move to the next digit.
• Continue programming all 6 digits in this way. When finished, press the “SELECT” button
and your entered code will be saved.
• To program your next code, press the “UP” arrow to go to the next code loca-
tion.
• When you have entered all your desired codes, press the “MENU” button to store your
settings.
Page 8
WR-300 Owner’s Manual
Reviewing Stored S.A.M.E. Codes
To review your saved S.A.M.E. codes, do the following:
• Press the “MENU” button.
• Press the “UP” arrow until “COUNTY CODE” is displayed on the screen.
• Press “SELECT”
• Use the “UP” arrow to scroll through the S.A.M.E. memory code locations.
• All empty memory locations will appear as “------”.
• Press the “MENU” button when finished reviewing the S.A.M.E. codes.
Choosing an Alert Type (Voice or Siren):
1. Press the “MENU” button to open menu options.
2. Press the “UP” arrow until Alert Mode is displayed on the screen. Press the “SELECT”
button and “VOICE” will start blinking.
3. If you want the voice alert, press the “SELECT” button.
4. If “VOICE” is chosen, the alert would sound for 8 seconds followed by 5
minutes of weather broadcast.
5. If you want the siren alert, press the “UP” arrow until “SIREN” is displayed,
then press the “SELECT” button to save your setting.
6. If “SIREN” is chosen, alert tones will sound for 5 minutes or until the “ALERT
ON/OFF” button is pressed.
To Turn the Alert ON and OFF:
To turn the alert on and off, press and hold the “ALERT ON/OFF” button for 5 seconds until
you see “ALERT ON” blinking. While still holding down the button, press the “UP” arrow to
switch between “ALERT ON” and “ALERT OFF”. Press the “SELECT” button to save your
selection.
Setting the Alert Volume:
• To set the alert volume, press the “MENU” button.
• Press the “UP” arrow until “SIREN LEVEL” is displayed.
• Press the “SELECT” button and “LEVEL HIGH” or “LEVEL LO” will start blinking.
• Then press the “UP” arrow to choose “LEVEL HI” or “LEVEL LO” volume.
• Press the “SELECT” button to save your setting.
Selectable Alert Option:
You can program the WR-300 weather radio to only sound the voice or siren alert for certain
weather emergency messages. Those messages unimportant to you can be programmed to
only display a message, minimizing annoyance.
To program the emergeny messages you want to silence, do the following:
•
•
•
Press the “MENU” button until “DEFEAT SIREN” is displayed. Press the “SELECT”button.
Using the “UP” arrow, scroll through the different alerts you may want to silence.
When you have selected one, press the “RIGHT” arrow to change the status of the event
from “ALERT ENABLE” to “ALERT DISABLE”.
•
Press the “MENU” button to save your selection and exit the programming option.
Page 9
WR-300 Owner’s Manual
Testing the Alert:
To test the alert function to ensure it is working, press the “MENU” button, then press the
“UP” arrow until “SIREN TEST” is displayed. Press the “SELECT” button to sound the alert
siren. Press the “SELECT” button again to silence the alarm.
Reviewing Alerts:
The WR-300 weather radio can store 10 different alerts (with overlapping effective times) in
its memory. If the radio receives a new alert while a previous alert is still in effect, it automati-
cally displays the new alert description. To review past alerts that are still in effect, press the
“DOWN” arrow to scroll through the last 10 alerts. If an alert is expired, it will be marked
“EXP”.
Test Signals Broadcast by NWS:
All National Weather Service stations periodically transmit test signals. You can find out when
your local NWS station broadcasts test signals by calling the NOAA National Weather Service
Forecast Office (listed under “Weather” in the Federal Government section of the telephone
book.)
During the weekly test signal, the local NWS station will give a list of counties covered by
their transmitter. The NWS test signal allows everyone with weather radio receivers to verify
the operation of their equipment.
The following test signals may be sent by the NWS during testing: required weekly test,
required monthly test, system demo, and national periodic test.
No Reception Warning:
If no alerts are received for 10 days, the display will flash “CHECK RECEPTION” every 30
seconds. If this happens, check your channel settings and county codes for setting errors. If
you receive a clear signal from the NWS, try using the “ALL” county code setting to receive
all alerts for all counties.
Note: If you have trouble finding reception, please move your radio closer to a window and
away from flourescent lighting.
Page 10
WR-300 Owner’s Manual
AM/FM Radio:
There is an AM/FM radio built into the WR-300 weather radio that you can listen to without
interrupting the weather radio functions. If an alert is received, the radio automatically switches
from the AM/FM radio to the weather radio alert.
Turning the AM/FM Radio On: Press the “RADIO” button to turn the AM/FM radio on and
off.
Changing AM/FM Stations: Press the “RIGHT” arrow or “LEFT” arrow to scan through the
radio stations. When you find a station you like, stop pressing the arrow and the radio will
stay on that station.
AM/FM Memory Channels: You can program 3 AM and 3 FM radio stations into the radio’s
memory. To program a memory channel, do the following:
• Turn the AM/FM radio on and use the “LEFT” or “RIGHT” arrow to tune to the desired
station.
• Press the “MENU” button. The “MEMORY” number will flash on the display.
• Use the “UP” or “DOWN” arrow to choose the desired memory channel you wish to prog-
ram.
• Press the “SELECT” button to save your frequency selection to the chosen memory chan-
nel.
Page 11
WR-300 Owner’s Manual
Troubleshooting:
Problem
Suggestion
Make sure the AC Power Adapter is
securely plugged into both DC jack on back
of weather radio and into wall outlet. Make
sure batteries are installed in case AC
power fails.
No power
Check VOLUME control to ensure volume
is turned up to an audible level.
No sound
Ensure that telescoping antenna is up and
fully extended.
If you are using an external antenna,
ensure that it is connected properly.
Ensure that the radio is set to the NWS
weather channel in use in your area.
No weather broadcast when you press
WEATHER/ SNOOZE button
Contact NWS to ensure they are presently
broadcasting.
If in a metal structure, make sure you are
close to a window.
If in a weak signal area, you will need an
external antenna.
Check to see that you have programmed in
the correct S.A.M.E. County Code(s).
The radio is not responding properly to
NWS weather alert broadcasts
Check with the NWS that the tower is
broadcasting.
Page 12
WR-300 Owner’s Manual
,
Reception:
The National Weather Service operates a system of weather and hazard alert broadcasts cov-
ering a large area of the United States. Currently, only a few areas are not covered. Typical
broadcasts are within reception distance of 25-50 miles of the weather station. Your WR-300
weather radio can receive broadcasts from up to 50 miles from the weather station, depending
on your location and conditions of weather, terrain, etc. If you find reception is not good in your
area, try different locations in your home or office to find a spot of improved reception.
Placement near a window usually improves reception.
If a weather broadcast cannot be heard on any of the 7 channels, contact your local
NWS office and verify the closest station is on air. Also verify the channel frequencies the sta-
tion is broadcasting. If your NWS is transmitting and you are not receiving the broadcasts,
you may need an external antenna. Please visit our website at www.midlandradio.com to
view our suggested antenna, the 18-259W VHF Through-Glass Antenna. This antenna
improves reception when applied to a window.
Please note: Metal structures are more difficult to receive reception in, because metal inter-
feres with the signal. If you live in a metal structure, you may need an external antenna.
Page 13
WR-300 Owner’s Manual
About NOAA, NWS, & S.A.M.E. County Codes
In 1994, NOAA began broadcasting coded emergency signals that identify the specific geo-
graphic area (such as the county within a state) that is affected by an emergency. Until that
time, such specific emergency weather information was not available directly to the public.
NOAA transmits the coded emergency signals using a technique called Specific Area
Message Encoding (S.A.M.E.) The WR-300 weather radio is designed to receive these
S.A.M.E. county code transmissions.
The National Weather service divides the United States by state and county (or parish)
and assigns a six digit code number called a FIPS (Federal Information Processing System)
code, also known as a S.A.M.E. county code.
You can program the weather radio with up to 23 S.A.M.E. county codes. The weather radio
allows you to receive broadcast alerts for either your own county, or for up to 23 counties.
This will eliminate any alerts that are not within your area of interest.
When you program your S.A.M.E. county code(s) into the WR-300 weather radio, you
eliminate any alerts that are not within those counties. Warnings, watches and advisories of
weather and other area emergencies, about 50 different types, will activate the weather
radio for only your programmed specific area.
The S.A.M.E. message the NWS sends contains information pertaining to the period for
which the alert is valid. NWS can set the active time of the alert from 15 minutes up to 6
hours. When the designated time has passed, the weather radio display message and light
will automatically reset to their normal appearance.
Page 14
WR-300 Owner’s Manual
S.A.M.E. County Code Record:
County Name
S.A.M.E. County Code
NWS Channel
Page 15
WR-300 Owner’s Manual
Specifications:
Specifications are nominal and subject to change.
General
Frequency Range
(162.40, 162.425, 162.45, 162.475, 162.50, 162.525,
162.55 MHz)
Number of WX Channels
Input Voltage
7
9-14 Volts DC
7.0x5.5x2.25
0.5 uV
Dimensions
20 dB Quieting Sensitivity
FIPS County code Sensitivity at5kHz Dev
Channel Selectivity
0.5uV
±25kHz, 60dB
8 ohms
Speaker Impedance
Speaker Output at10%THD
200 mW max.
FCC Compliance Information:
MIDLAND (NOAA) Weather Radio Model WR-300, “S.A.M.E. Digital Weather/Hazard Alert
Radio”. This device complies with part 15 of the FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) This device may not cause harmful interference; (2) This device
must accept any interference received including interference that may cause undesired oper-
ation.
Page 16
WR-300 Owner’s Manual
One Year Limited Warranty:
MIDLAND Radio Corporation will repair or replace, at its option without charge, your WR-300
weather radio which fails due to a defect in material or workmanship within one year follow-
ing the initial consumer purchase.
This warranty does not include any antennas, which may be a part of or included with the
warranted product, or the cost of labor for removal or re-installation of the product in a vehi-
cle or other mounting.
Performance of any obligation under this warranty may be obtained by returning the warrant-
ed product, freight prepaid, along with a copy of the original sales receipt to Midland Radio
Corporation at the address provided below.
This warranty gives you specific legal rights, and you may also have other rights, which vary,
from state to state.
Note: The above warranty applies only to merchandise purchased in the United States of
America or any of the territories or possessions thereof, or from a U.S. Military exchange.
For warranty coverage on merchandise purchased elsewhere, ask your dealer.
Midland Radio Corporation
Warranty Service Department
5900 Parretta Drive
Kansas City, Missouri 64120
Phone: (816) 241-8500
Fax: (816) 241-5713
E-mail: [email protected]
Page 17
WR-300 Owner’s Manual
Service:
If your MIDLAND Weather Radio fails to operate properly, check the “Troubleshooting” section
in this manual before returning it for service. If necessary, return as follows:
1. Pack the unit in its original box and packing. Then pack the original box in a
suitable shipping carton. Caution: Improper packing may result in damage
during shipment.
2. Include the following:
a. full description of any problems
b. money order for $7.50 to cover shipping and handling (this may not be
required in some states)
c. daytime telephone number, name & address
3. For warranty service include a photocopy of the bill of sale from an authorized dealer
or other proof of purchase showing the date of sale.
4. You do not need to return accessory items (AC/DC Adapter, batteries, Owners Guide)
unless they might be directly related to the problem.
5. A flat rate of $45.00 will apply to repairs not covered by warranty or units
that are over one year old. Send only cashier’s check, money order or
Master Card or Visa card number.
Page 18
WR-300 Owner’s Manual
Page 19
|