Linear Satellite Radio GT 30 User Manual

DESCRIPTION  
PROGRAM TRANSMITTER INTO RECEIVER  
Linear’s GT series of digital transmitters are wireless For INTELLICODEand CodeDodgersystems, refer  
radio controls designed for use with Genie Pro® to the instructions provided with the receiver to set it to a  
INTELLICODE™, Overhead Door® CodeDodger™, and learningmode. Activate the desired transmitter button  
Linear® Model AM-RGR access control receivers. The to program that button into the receiver  
rolling-code GT radio format provides additional security  
GT-30  
by changing the transmitter’s code with each use.  
The GT-30 is a three-button transmitter that sends a  
unique code for each button.Typically, one button is used  
to operate a community access gate, another button can  
activate the individual’s garage door, and a third button  
can control an additional door or other device.  
DIGITAL  
TRANSMITTER  
The transmitter is powered by two Type 2016 “coin cell”  
batteries. A red indicator lights when the transmitter is  
activated. A removable spring steel visor clip is supplied  
attached to the back of the transmitter.  
Linears Model AM-RGR receivers detect the signal from  
the transmitter and pass its digital code to the AM/II  
access controller.  
Operation Instructions  
NOTE: INTELLICODE™, CodeDodger™, Genie Pro®, and Overhead  
Door® are registered trademarks of Overhead Door Corporation.  
GT-30 transmitters are manufactured and sold Block  
Codedfrom the factory. Each block of transmitters is  
labeled with the starting and ending block code number,  
along with a facility code number. Refer to the AM/II  
instructions for details on how to program the block and  
facility code numbers into the controller.  
(760) 438-7000 • FAX (760) 438-7043  
USA & Canada (800) 421-1587 & (800) 392-0123  
Toll Free FAX (800) 468-1340  
REPLACING BATTERIES  
LINEAR LIMITED WARRANTY  
This Linear product is warranted against defects in material and workmanship for twelve (12)  
months. The Warranty Expiration Date is labeled on the product. This warranty extends only  
to wholesale customers who buy direct from Linear or through Linear’s normal distribution  
channels. Linear does not warrant this product to consumers. Consumers should inquire from  
their selling dealer as to the nature of the dealers warranty, if any. There are no obligations or  
liabilities on the part of Linear corporation for consequential damages arising out of or in  
connection with use or performance of this product or other indirect damages with respect  
to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation.  
All implied warranties, including implied warranties for merchantability and implied warranties  
for fitness, are valid only until Warranty Expiration Date as labeled on the product. This Linear  
Corporation Warranty is in lieu of all other warranties express or implied.  
When the red indicator on the face of the transmitter  
lights dimly, or not at all during activation, the batteries  
need replacing.  
2
CAREFULLY REMOVE  
CIRCUIT BOARD  
1
All products returned for warranty service require a Return Product Authorization Number (RPA#).  
Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.  
REMOVE VISOR  
CLIP AND SCREW  
IMPORTANT !!!  
Linear radio controls provide a reliable communications link and ll an important need in portable  
wireless signaling. However, there are some limitations which must be observed.  
INSTALL TWO  
TYPE 2016 BATTERIES  
3
PLUS (+) SIDE DOWN  
For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15  
devices. As such, they have limited transmitter power and therefore limited range.  
A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio  
signals that occur on or near their operating frequencies, regardless of code settings.  
Changes or modications to the device may void FCC compliance.  
Infrequently used radio links should be tested regularly to protect against undetected interference or fault.  
A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor  
or dealer, and these facts should be communicated to the ultimate users.  
This device complies with FCC Part 15. Operation is subject to the following two conditions: (1) This device  
may not cause harmful interference and (2) this device must accept any interference received, including  
interference that may cause undesired operation.  
REASSEMBLE  
UNIT WHEN  
FINISHED  
Copyright © 2000 Linear Corporation  
217130 A  
 

Land Pride Brush Cutter RCB6610 User Manual
Lennox Hearth Indoor Fireplace CVF LP User Manual
Lenoxx Electronics Telephone H 5560 User Manual
LG Electronics Personal Computer D4470 User Manual
Linn Stereo Amplifier Akurate Kontrol Pre Amplifier User Manual
Magnasonic Flat Panel Television 14611MHD User Manual
Makita Chainsaw UC 3001A User Manual
Manley Labs Power Supply 20 BIT DIGITAL TO ANALOG CONVERTER User Manual
Maytag Dishwasher W10185071B User Manual
MGE UPS Systems Power Supply 225KVA User Manual